Manufacturing specifications for plastic molds
Publish:
2023-03-07 14:34
Source:
Manufacturing specifications for plastic molds
I. Confirmation drawing:
A. Waterway:
1. Male mold&female mold: It depends on the shape of the finished product. The path and quantity of water circulation should be coordinated
2. Stripper plate x 2 cycles.
The above water hole joints need to be countersunk, with a size of $35 * L25mm.
"At the water plug of the mold, it is necessary to indicate IN, OUT, and number.".
5. It is necessary to attach copper water hydrants, A01&A07 are plastic water hydrants, and A09 copper water hydrants have a size of 1/4 "PT.
6. The method of making side water stop bolts is 2 PCS water stop bolts or 1 PCS water stop bolts+copper blocks.
If there is a water spray hole, use a copper sheet as a separator.
B. Material trench: Design the path, shape, size, etc. of the material trench based on the balance of finished product feeding.
C. Entry point: The type of entry point is determined based on the appearance shape and requirements of the finished product, including needle point, side needle point, side edge shape, cone shape, etc.
D. Ejection method:
PIN ejection requires the use of the DME specification (depending on different customers).
When the finished surface of the thimble has a shape, directional positioning is required.
3. Ejection ring (pay special attention to the draft angle of the water ring) or ejection block.
E. Positioning block X4: lengthen the square positioning block on the male and female templates 360 degrees/4 to increase the accuracy of the reference plane (material: SKD-61) China Plastic Mold Network
F. Moulding method:
1. The more screws used to lock the male and female mold kernels, the better they should be designed, and they should be evenly distributed to make the contact surface between the mold kernels and the mold base more closely fit
When locking the screws, it is necessary to seal and lock them in with consistent torque.
Both male and female mold kernels must have positioning pins that snap into the mold base.
3. When the mold core shape of all inserts is circular, positioning is required, and it can only be assembled in one direction to avoid incorrect orientation during assembly.
G.4 The guide pillar shall have 1 pcs. of eccentricity, with X and Y axes offset by 10mm respectively.
H. The screw holes and screws of the mold must comply with the metric specifications of the DME.
I. The edge sealing of the return pin shall have a resistant top plate made of TDAC+nitriding treatment.
J. If there are inclined pins and sliders, wear plates should be added on three sides, and there must be oil grooves (material: TDAC+nitriding treatment).
K. Counter needs to be installed, INSERT type (only required by A09 customers).
The length, width, height, positioning ring, and KO hole of the mold should match the customer's machine size.
M. If it is a three plate mold, A09 is the external shutter, and A is the internal shutter.
N. Check whether the separation distance between the mother mold and the stripper plate is sufficient. The robot takes out the material head, considering the length of the LGP and the length of the machine
Maximum stroke.
O. The mold should have an arrow indicating electrical discharge machining.
P. Name Plate, arrow, mold lock, Part No., date stamp, hole number, recycling stamp, counter, etc., need to be marked on the structural drawing.
When the mold is shipped, the arrows need to be painted yellow, and the lock module needs to be painted red.
When the mold needs to be forcibly repositioned, it is necessary to affix a forced repositioning nameplate under the arrow on the mold foot.
S. All slider mechanisms require springs.
T. All BUSH shall be provided with positioning pins.
It is necessary to pay attention to the problem of shrinkage, especially the size of the assembly.
V. Regulations on layers and lines of mold structure drawing:
1. Center line ----------- pink.
2. Material trench ----------- yellow.
3. Waterway ----------- Light orange.
4. Dimension lines, explanatory text&material list ----------- blue color.
5. Mold structure:
A. Appearance ---------- black.
B. Mechanism (slider, inclined pin, pressure cylinder, etc.) ----------- water blue color.
Parts of spare parts (screws, shafts, thimbles, etc.) --------- violet blue.
6. Finished product&Honghan Logo -------- green.
The manufacturer must provide mold structure drawings and detailed parts drawings.
X. It is necessary to understand who makes drawings, mold base processing, NC processing, grinding processing, etc.
Related News
Due to the superior performance that many traditional insulators cannot match, silicone rubber high-voltage composite insulators have been increasingly used at home and abroad. The research and development of silicone rubber high-voltage composite insulators in China is relatively late, but they are also developing rapidly. According to information
Powder with high hardness, low plasticity, and high friction has poor compaction performance
The smoother the surface of the molding mold, the higher the hardness, and the greater the rigidity, the more conducive to the improvement and uniformity of the density of the damaged body; The green body density using two-way pressing is higher than that using one-way pressing,
The gate is directly related to the beauty of the plastic part. If the gate design is not good, it is prone to defects. It is easy to generate serpentine flow without any obstruction. For products with high requirements, overflow and exhaust should also be designed.
Analysis on composition and structure of plastic injection mold
Plastic injection molds are basically divided into static and dynamic molds. The injection head side of the injection molding machine with a gate sleeve is a static mold, which generally consists of a gate sleeve, a backing plate, and a template. For simple molds, it is also possible to use a thicker template instead of a backing plate.
The accuracy of the mold will become higher and higher
The mold industry is an important component of China's hardware industry. The 12th Five Year Plan period is a key period for China to properly respond to major changes in the domestic and foreign development environment and accelerate the realization of the goal of building a moderately prosperous society in an all-round way
What are the main factors affecting the mold pressing process
Powders with high hardness, low plasticity, and high friction have poor compaction performance, which can be appropriately improved by adding lubricants or molding agents; When the powder purity is low and the oxygen content is high, the pressing performance is poor,