Analysis on composition and structure of plastic injection mold
Publish:
2023-03-07 14:37
Source:
Plastic injection molds are basically divided into static and dynamic molds. The injection head side of the injection molding machine with a gate sleeve is a static mold, which generally consists of a gate sleeve, a backing plate, and a template. For simple molds, it is also possible to use a thicker template instead of a backing plate. The sprue sleeve is generally a standard part, and it is not recommended to cancel it unless for special reasons. The use of the sprue sleeve is beneficial for installing the mold, facilitating replacement, and eliminating the need for self polishing. Some special mold runner sleeves can be drilled out or cut with a taper line. When static mold release is necessary for some molds, a static mold release mechanism must also be added. The structure of a moving mold is generally a moving template, a moving mold backing plate, a mold release mechanism, and a mold foot and mounting plate.
In addition to the stripper bar, there are also return bars in the mold release mechanism. Some molds also need to add springs to achieve functions such as automatic mold release. There are also guide pillars, cooling water holes, flow channels, and other essential basic structures of the mold. Of course, there are also inclined guide molds, such as inclined guide boxes and columns. When designing a mold for a product, it is first necessary to set the basic structural dimensions of the mold to prepare materials to speed up mold manufacturing. For complex products, the product drawing should be drawn first, and then the mold size should be determined.
Currently, molds are basically subjected to heat treatment to increase their hardness and improve their service life. Before heat treatment, perform preliminary processing on the template: drill guide post holes, return holes (dynamic molds), mold cavity holes, screw holes, gate sleeve holes (dynamic molds), cooling water holes, etc., and mill the flow channels and mold cavities. In some molds, the inclined guide box should also be milled. Currently, the templates for ordinary precision molds generally use cr12, cr12mov, and some professional mold steels. The hardness of cr12 and other materials cannot be too high, and they often crack at HRC60 degrees. The common hardness of templates is generally around HRC55 degrees. The hardness of the core can be above HRC58. If the material is 3Cr2w8v, the surface hardness shall be nitrided after manufacturing, and the hardness shall be above HRC58. The thicker the nitrided layer, the better.
The gate is directly related to the beauty of the plastic part. If the gate design is not good, it is prone to defects. It is easy to generate serpentine flow without any obstruction. For products with high requirements, overflow and exhaust should also be designed. An ejector rod can be used at the overflow point, and there should be no overflow flash on the template, so as not to affect the mold life. There are more and more mold design software, and most of them rarely use pencils to draw mold drawings.
Related News
Due to the superior performance that many traditional insulators cannot match, silicone rubber high-voltage composite insulators have been increasingly used at home and abroad. The research and development of silicone rubber high-voltage composite insulators in China is relatively late, but they are also developing rapidly. According to information
Powder with high hardness, low plasticity, and high friction has poor compaction performance
The smoother the surface of the molding mold, the higher the hardness, and the greater the rigidity, the more conducive to the improvement and uniformity of the density of the damaged body; The green body density using two-way pressing is higher than that using one-way pressing,
The gate is directly related to the beauty of the plastic part. If the gate design is not good, it is prone to defects. It is easy to generate serpentine flow without any obstruction. For products with high requirements, overflow and exhaust should also be designed.
Analysis on composition and structure of plastic injection mold
Plastic injection molds are basically divided into static and dynamic molds. The injection head side of the injection molding machine with a gate sleeve is a static mold, which generally consists of a gate sleeve, a backing plate, and a template. For simple molds, it is also possible to use a thicker template instead of a backing plate.
The accuracy of the mold will become higher and higher
The mold industry is an important component of China's hardware industry. The 12th Five Year Plan period is a key period for China to properly respond to major changes in the domestic and foreign development environment and accelerate the realization of the goal of building a moderately prosperous society in an all-round way
What are the main factors affecting the mold pressing process
Powders with high hardness, low plasticity, and high friction have poor compaction performance, which can be appropriately improved by adding lubricants or molding agents; When the powder purity is low and the oxygen content is high, the pressing performance is poor,